Tuesday, August 26, 2025

My bike, wheels, mudguard, loom, footpegs

This week I needed to progress with the final big jobs, firstly the wheels were looking worse the more i looked at them, I found a local dealer (to me) in Waterlooville called Bike Shed who could remove my tyres while I waited. They are a little local motorcycle workshop run by a couple who had been there for 19 years, super nice people, very chatty, very old school in a good way, I be using them again!




Ive now removed the front disc and the front wheel bearings and dropped them round to Plasticoat Powder coaters who I have used before

I fitted the rear inner mud guard, routed the zip tied the loom, fitted the rear foot pegs and generally replaced and bolts and nuts with stainless items.


Saddle

I had previously ordered a pair of seat covers from a company in Italy called Volcano Industry I got say these are amazing, fit, finish, colour all spot on. The covers are tailored to the original shape with an elastic strap sewn on the inside with you can pull about and staple down. I actually run out of staples so the job his half finished until more turn up this week. I will post again the finished articles.









Thursday, August 21, 2025

My bike, Footrest and fairing

The riders side front rear set was snapped on the heal guard, I had previously got the replacement I just needed to get round to fitting it.


As I swapped everything over I cleaned, polished and replaced all the nuts and bolts with replacement stainless items.

Rear set main bolts, M8 x 30mm socket head x 2 plus 2 x M8 nyloc nuts

Spring bolt pedal side, M6 nyloc nut

Rear brake cylinder plunger nut, M6 nyloc nut

Mater cylinder bolys 2 x M6 x ? bolts plus 2 x M6 Nyloc nuts

Fairing lowers

I decided to fit the decals I had previously bought to the fairing lowers. 

Using the original sales brochure as a guide I started with the big 'A' in line with the front of the fairing edge. the lower part will overlay on the fairing vents so some cutting is required.

Next I fitted the green and red triangles, because of the curves I cut them in to two separate parts and installed them separately, I used a hair dryer hear to get round the corners.

Next the white 'aprilia' word, the 'P' bleeds in to the white and used spaced accordingly.

Next, sponsor stickers, these just aligned as per brochure.

Thoughts? Firstly I will say some of the scale of these stickers is questionable, so it is difficult to make it look 100%. Secondly I think I made the white spacing a little tight, if I did it again (and I may do) and would make the white lines thicker. But there is no instructions for this, you just got to give it a go and if it looks right to the eye, it probably is.



OG panel for reference 

UPDATE

Feeling brave I decided to see if I could remove the flag elements and re-position them, this worked out much better than expected and I am much happier with the placement now.




Monday, August 11, 2025

my bike, sprocket carrier updates

This week I decided to re-furbish the sprocket carrier and get a few more parts on the bike, to help with this I ordered a stainless bolt kit of ebay that was listed for the AF1... 

Sprocket carrier: The carrier had previously been (badly) painted and generally looked poor so I first went over with a course and then a fine wet and dry paper to get the worst off. There were lots of paint flakes that came off as the alloy had oxidised in a couple of places lifting the paint. It looked ok, then I dusted it with primer and quite frankly it looked dreadful. The original paint reacted with the primer and listed anything with an edge on it, the only solution was to paint strip it to bare metal and start again.

paint disaster
paint stripped

From here I masked the critical areas and lightly dusted with grey primer, some parts still didn't look great, so these were rubbed down with fine wet and dry and re-painted with the primer. Luckily it was a hot day and the paint dried quickly, so i could afford to go light and slow. 

primed and ready

The next stage is paint, there are a million silvers out there, I chose Porsche silver as it sounds more fancy...

now as fast as a GT3 RS...

Bolt kit: For ease and because its not going to be a full on factory restoration I decided to buy a stainless steel bolt kit off ebay, the dealer had multiple listings with different models in the title, i chose the appropriate one for my bike. Upon arrival of the kit I was slightly annoyed to see it was a more generic bolt kit and for example it had no M8 x 30mm dome head bolts for holding the sub frame on. I checked the listing and rather frustratingly it said 'a selection of common nuts and bolts and not model specific'. I should of read the small print and if i noticed that I wouldn't of ordered, so don't to what I did, read the listing in full before ordering. 
I ordered some M8 x 30's on amazon and had them the next day so I could install the subframe. With the subframe on its tricky to get the airbox fitted. To do so I removed the lid and filter, it also helps getting the connecting hose on to the air box as you can see inside, then refit the filter and lid.







My bike, tyres and final assembly

 I bit the bullet and ordered new tyres as I just couldn't bring myself to re-fit the old Avons as they are around 7 years old. I chose ...